Cisco CCNA Certification Exam Tutorial: Keep Your Most Important Appointment

Imagine this. You have an appointment with a client to work on a server or router install. A few minutes before you're scheduled to be there, you decide there's something really good on TV you'd like to watch. Or you decide to go to the gym, or play a game, or do anything else except go see the client. Even if you weren't going to get fired for not showing up, it's certainly unfair to the client. You've got a professional obligation, and you should be there on time.

Now, what's this got to do with you becoming a CCNA or CCNP? Plenty. Because when it comes to your study time, you're the client. You owe it to yourself to show up. You would never blow off an appointment to meet a client to get some important work done.

First, though, you have to make that appointment with yourself! Schedule your CCNA / CCNP study time, and keep that appointment as you would with a client. Turn off the TV, your cell, your iPod, and everything else electronic that you carry around. Believe it or not, the world can survive with being in contact with you for an hour or so! You might even like it!

Getting certified isn't about how many hours, days, or weeks you spend studying. It's about how much quality time you put in. Be honest with yourself and realize that you're better off with 45 minutes of uninterrupted study as you would be with three hours of constantly interrupted study.

Don't blow off an appointment to yourself, either. Schedule the time, be there on time, get your study done, and you're one step closer to your CCNA and CCNP!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNA and CCNP tutorials! For my FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies. Get your CCNA study guide from The Bryant Advantage!

Cisco CCNP / BSCI Exam Tutorial: Ten IP Routing Details You Must Know!

To pass the BSCI exam and earn your CCNP, you've got to keep a lot of details in mind. It's easy to overlook the "simpler" protocols and services such as static routing and distance vector protocols. With this in mind, here's a quick review of some details you should know for success in the exam room and real-world networks!

When packets need to be routed, the routing table is parsed for the longest prefix match if multiple paths exist with the same prefix length, the route with the lowest AD is preferred. If there are still multiple valid paths, equal-cost load-sharing goes into effect.

The ip route command is used to create static routes the command ip route 0.0.0.0 0.0.0.0 < next-hop-IP or local exit interface> creates a default static route.

A static route with a next-hop IP address has an AD of one, while a static route with a local exit interface has an AD of zero.

A floating static route is a static route with an AD higher than that of the dynamic routing protocols running on the router, ensuring that the static route can only be used if the routing protocol goes down.

On-Demand Routing (ODR) is only appropriate in a hub-and-spoke network. The spokes effectively become stub routers. ODR uses Cisco Discovery Protocol (CDP) to send route information.

To propagate a default route with IP routing, use the ip default-network command. To do so with IP routing disabled, use ip default-gateway. You can also redistribute a static route into most protocols, but not IGRP. IGRP does not understand a static route to 0.0.0.0.

The ip helper-address command takes certain broadcasts and translates then into unicasts in order to allow the router to forward them. These default ports are:

TIME, port 37

TACACS, port 49

DNS, port 53

BOOTP/DHCP Server, port 67

BOOTP/DHCP Client, port 68

TFTP, port 69

NetBIOS name service, port 137

NetBIOS datagram services, port 138

To name other ports, use the ip forward-protocol command. To remove any of these ports from the default list, use the no ip forward-protocol command.

ICMP Router Discovery Protocol (IRDP) hosts hear multicast Hellos from routers, allowing host-router discovery. HSRP routers create a virtual router that hosts think is a real router. Both protocols help networks cut over to a functional router quickly when their primary router goes down.

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNA and CCNP tutorials! For my FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies. Get your CCNA study guide from The Bryant Advantage!

CCNA Certification Exam Tutorial: Cisco Switching Modes

To pass the CCNA exam and earn this important certification, you've got to know switching inside and out. While you're learning all the basic switching theory, make sure to spend some time with the one of three switching modes Cisco routers can use.

Store-and-Forward is exactly what it sounds like. The entire frame will be stored before it is forwarded. This mode allows for the greatest amount of error checking, since a CRC (Cyclical Redundancy Check) is run against the frame before it is forwarded. If the frame contains an error, it is discarded. If there's no problem with the frame, the frame is then forwarded to its proper destination.

While store-and-forward does perform error checking, the delay in processing the frame while this error check is run results in higher latency than the other modes you're about to read about. The latency time can also vary, since not all frames are the same size.

Cut-through switching copies only the destination MAC address into its memory before beginning to forward the frame. Since the frame is being forwarded as soon as the destination MAC is read, there is less latency than store-and-forward. The drawback is that there is no error checking.

There is a middle ground, fragment-free switching. Only part of the frame is copied to memory before it is forwarded, but it's the first 64 bytes of the frame, not just the destination MAC. (Why? Because if there is a problem with the frame, it's most likely in the first 64 bytes.) There is a little more error checking than cut-through, but not as much latency as with store-and-forward.

Note that the latency of both cut-through and fragment-free is fixed; these modes always look at the first six or 64 bytes, respectively. Store-and-forward's latency depends on the size of the frame. Learning the similarities and differences between these modes is an often-overlooked part of CCNA studies. Spend some time studying this important CCNA topic - you'll be glad you did!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNA and CCNP tutorials! For my FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies. Get your CCNA study guide from The Bryant Advantage!

Cisco CCNA Certification Exam Tutorial: Access List Details You Must Know!

To pass the CCNA exam, you have to be able to write and troubleshoot access lists. As you climb the ladder toward the CCNP and CCIE, you'll see more and more uses for ACLs. Therefore, you had better know the basics!

The use of "host" and "any" confuses some newcomers to ACLs, so let's take a look at that first.

It is acceptable to configure a wildcard mask of all ones or all zeroes. A wildcard mask of 0.0.0.0 means the address specified in the ACL line must be matched exactly a wildcard mask of 255.255.255.255 means that all addresses will match the line.

Wildcard masks have the option of using the word host to represent a wildcard mask of 0.0.0.0. Consider a configuration where only packets from IP source 10.1.1.1 should be allowed and all other packets denied. The following ACLs both do that.

R3#conf t

R3(config)#access-list 6 permit 10.1.1.1 0.0.0.0

R3(config)#conf t

R3(config)#access-list 7 permit host 10.1.1.1

The keyword any can be used to represent a wildcard mask of 255.255.255.255.

R3(config)#access-list 15 permit any

Another often overlooked detail is the order of the lines in an ACL. Even in a two- or three-line ACL, the order of the lines in an ACL is vital.

Consider a situation where packets sourced from 172.18.18.0 /24 will be denied, but all others will be permitted. The following ACL would do that.

R3#conf t

R3(config)#access-list 15 deny 172.18.18.0 0.0.0.255

R3(config)#access-list 15 permit any

The previous example also illustrates the importance of configuring the ACL with the lines in the correct order to get the desired results. What would be the result if the lines were reversed?

R3#conf t

R3(config)#access-list 15 permit any

R3(config)#access-list 15 deny 172.18.18.0 0.0.0.255

If the lines were reversed, traffic from 172.18.18.0 /24 would be matched against the first line of the ACL. The first line is "permit any", meaning all traffic is permitted. The traffic from 172.18.18.0/24 matches that line, the traffic is permitted, and the ACL stops running. The statement denying the traffic from 172.18.18.0 is never run.

The key to writing and troubleshoot access lists is to take just an extra moment to read it over and make sure it's going to do what you intend it to do. It's better to realize your mistake on paper instead of once the ACL's been applied to an interface!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNP and CCNA tutorials! For my FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies. Pass your CCNP exam with The Bryant Advantage!

Cisco CCNA Certification Exam Tutorial: Variance And Unequal Cost Load Balancing

To pass the CCNA exam, you've got to know how to work with IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure that all paths are in use while allowing for varying bandwidth rates.

Using the variance command is the easy part - it's getting the metric that's the hard part with IGRP. With EIGRP, you just look in the topology table and that's it. With IGRP, you've got to run a debug to get the right metric.

The variance command is a multiplier when the value supplied with the variance command is multiplied by the lowest-cost metric, it must exceed the higher-cost metric in order for the higher-cost route to be added.

If that sounds complicated, it's not. It's one of those things that sounds difficult, but isn't. Trust me!

In this example, R1 has two paths to 172.23.0.0, but is currently using only one. By looking in the IP routing table, we've seen that the lowest-cost metric for network 172.23.0.0 on R1 is 8576. This path goes through the 172.12.123.0 network. There is another valid path that uses the 172.12.13.0 network, but is not currently in use.

I 172.23.0.0/16 [100/8576] via 172.12.123.2, 00:00:53, Serial0

IGRP does not have a "show" command that displays all valid routes to a destination, as does EIGRP. The command debug ip igrp transactions will show the current metric of the routes using the 512 KBPS route.

R1#debug ip igrp transactions

IGRP protocol debugging is on

19:17:51: IGRP: broadcasting request on Loopback0

19:17:51: IGRP: broadcasting request on Serial0

19:17:51: IGRP: broadcasting request on Serial1

19:17:51: IGRP: received update from 172.12.13.3 on Serial1

19:17:51: subnet 172.12.13.0, metric 23531 (neighbor 21531)

19:17:51: subnet 172.12.123.0, metric 23531 (neighbor 8476)

19:17:51: network 1.0.0.0, metric 24031 (neighbor 8976)

19:17:51: network 2.0.0.0, metric 22131 (neighbor 1600)

19:17:51: network 3.0.0.0, metric 22031 (neighbor 501)

19:17:51: network 172.23.0.0, metric 21631 (neighbor 1100)

R1(config)#router igrp 1 R1(config-router)#variance 3 R1#show ip route 172.23.0.0 Routing entry for 172.23.0.0/16 Known via "igrp 1", distance 100, metric 8576 Redistributing via igrp 1 Advertised by igrp 1 (self originated) Last update from 172.12.123.2 on Serial0, 00:00:01 ago Routing Descriptor Blocks: * 172.12.13.3, from 172.12.13.3, 00:00:20 ago, via Serial1 Route metric is 21631, traffic share count is 1 Total delay is 21000 microseconds, minimum bandwidth is 512 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 0 172.12.123.3, from 172.12.123.3, 00:00:20 ago, via Serial0 Route metric is 8576, traffic share count is 3 Total delay is 21000 microseconds, minimum bandwidth is 1544 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 0 172.12.123.2, from 172.12.123.2, 00:00:01 ago, via Serial0 Route metric is 8576, traffic share count is 3 Total delay is 21000 microseconds, minimum bandwidth is 1544 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 0

The metric for 172.23.0.0 through the direct connection is 21631. A variance of 3 means that any route with a metric less than the best metric multiplied by the variance (in this case, 8576 x 3 = 25728) will be entered into the routing table. R1 now has three unequal-cost paths to 172.23.0.0 in its routing table, and load balancing will take place.

IGRP unequal-cost load balancing takes some practice, but as you can see, once you get the metric it's easy to work with. Just make sure you know how to get that metric!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNA and CCNP tutorials! For my FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies. Get your CCNA study guide from The Bryant Advantage!

Cisco CCNP / BCMSN Exam Tutorial: Multicasting And Reserved Addresses

Ever since you picked up your first CCNA book, you've heard about multicasting, gotten a fair idea of what it is, and you've memorized a couple of reserved multicasting addresses. Now as you prepare to pass the BCMSN exam and become a CCNP, you've got to take that knowledge to the next level and gain a true understanding of multicasting. Those of you with an eye on the CCIE will truly have to become multicasting experts!

Having said that, we're going to briefly review the basics of multicasting first, and then future tutorials will look at the different ways in which multicasting can be configured on Cisco routers and switches.

What Is Multicasting?

A unicast is data that is sent from one host to another, while a broadcast is data sent from a host that is destined for "all" host addresses. By "all", we can mean all hosts on a subnet, or truly all hosts on a network.

There's a quite a bit of a middle ground there! A multicast is that middle ground, as a multicast is data that is sent to a logical group of hosts, called a multicast group. Hosts that are not part of the multicast group will not receive the data.

Some other basic multicasting facts:

There's no limit on how many multicast groups a single host can belong to.

The sender is usually unaware of what host devices belong to the multicast group.

Multicast traffic is unidirectional. If the members of the multicast group need to respond, that reply will generally be a unicast.

The range of IP addresses reserved for multicasting is the Class D range, 224.0.0.0 - 239.255.255.255.

That range contains a couple of other reserved address ranges.

224.0.0.0 - 224.0.0.255 is reserved for network protocols only on a local network segment. Packets in this range will not be forwarded by routers, so these packets cannot leave the segment.

Just as Class A, Class B, and Class C networks have private address ranges, so does Class D. The Class D private address range is 239.0.0.0 - 239.255.255.255. Like the other private ranges, these addresses can't be routed, so they can be reused from one network to another.

The remaining addresses fall between 224.0.1.0 and 238.255.255.255. That's the "normal" range of multicast addresses. These addresses can be routed, so they must be unique and should not be duplicated from one network to the next.

In my next BCMSN / CCNP multicasting tutorial, we'll take a look at the different ways in which Cisco routers and switches interact to forward multicast traffic.

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNP and CCNA tutorials! For my FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies. Pass your CCNP exam with The Bryant Advantage!

Cisco CCNP/BCMSN Exam Tutorial: Changing Root Bridge Election Results

Your BCMSN and CCNP studies will include mastering the details of Spanning Tree Protocol (STP). While you learned some of these details in your CCNA studies, quite a bit of it may be new to you. Before going on to the intermediate and advanced STP features, let's review the root bridge election process and learn how to change these results.

Each switch will have a Bridge ID Priority value, more commonly referred to as a BID. This BID is a combination of a default priority value and the switch's MAC address, with the priority value listed first. For example, if a Cisco switch has the default priority value of 32,768 and a MAC address of 11-22-33-44-55-66, the BID would be 32768:11-22-33-44-55-66. Therefore, if the switch priority is left at the default, the MAC address is the deciding factor.

Switches are a lot like people - when they first arrive, they announce that they are the center of the universe! Unlike some people, the switches will soon get over it. BPDUs will be exchanged until one switch is elected Root Bridge, and it's the switch with the lowest BPDU that will end up being the Root Bridge.

If STP is left totally alone, a single switch is going to be the root bridge for every single VLAN in your network. Worse, that single switch is going to be selected because it has a lower MAC address than every other switch, which isn't exactly the criteria you want to use to select a single root bridge.

The time will definitely come when you want to determine a particular switch to be the root bridge for your VLANs, or when you will want to spread the root bridge workload. For instance, if you have 50 VLANs and five switches, you may want each switch to act as the root bridge for 10 VLANs each. You can make this happen with the spanning-tree vlan root command.

SW1(config)#spanning-tree vlan 1 ?

forward-time Set the forward delay for the spanning tree

hello-time Set the hello interval for the spanning tree

max-age Set the max age interval for the spanning tree

priority Set the bridge priority for the spanning tree

root Configure switch as root

In this example, we've got two switches, and SW1 has been elected the root bridge for VLANs 10, 20, and 30. We'll use the spanning-tree vlan root command on SW2 to make it the root bridge for VLANs 20 and 30.

SW2(config)#spanning-tree vlan 20 root primary

SW2(config)#spanning-tree vlan 30 root primary

SW2#show spanning vlan 20

VLAN0020

Spanning tree enabled protocol ieee

Root ID Priority 24596

Address 000f.90e2.1300

This bridge is the root

SW2#show spanning vlan 30

VLAN0030

Spanning tree enabled protocol ieee

Root ID Priority 24606

Address 000f.90e2.1300

This bridge is the root

SW 2 is now the root bridge for both VLAN 20 and 30. Notice that the priority value has changed from the default of 32768.

In the next CCNP / BCMSN tutorial, we'll take a look at more STP features.
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com ), home of free CCNA and CCNP tutorials, and The Ultimate CCNA and CCNP Study Packages.

Cisco CCNP/BSCI Exam Tutorial: Introduction To Policy Routing

Policy routing is a major topic on your BSCI exam, and you'll find quite a bit of policy routing going on in today's production networks. But what exactly is policy routing?

Policy-based routing, generally referred to as "policy routing", is the use of route maps to determine the path a packet will take to get to its final destination. As you progress through your CCNP studies and go on to the CCIE (or to a Cisco Quality Of Service certification), you'll find that traffic can be "marked" by policy routing in order to give different levels of service to various classes of traffic. (This is done by marking the traffic and placing the different classes of traffic in different queues in the router, allowing the administrator to give some traffic higher priority for transmission.)

There are some basic policy routing rules you should know:

Policy routing doesn't affect the destination of the packet, but does affect the path that is taken to get there.

Policy routing can forward traffic based on the source IP address or the destination IP address (with the use of an extended ACL).

Policy routing can be configured at the interface level, or globally.

Applying policy routing on an interface affects only packets arriving on that interface:

R2(config)#int s0

R2(config-if)#ip policy route-map CHANGE_NEXT_HOP

Applying the policy globally applies the route map to packets generated on the router, not on all packets received on all interfaces.

Whether you're running policy routing at the interface level, on packets created locally, or both, always run the command show ip policy to make sure you've got the right route maps on the proper interfaces.

R2#show ip policy

Interface Route map

local CHANGE_NEXT_HOP

Serial0 CHANGE_NEXT_HOP

And here's the big rule to remember....

If a packet doesn't match any of the specific criteria in a route map, or does match a line that has an explicit deny statement, the data is sent to the routing process and will be processed normally. If you don't want to route packets that do not meet any route map criteria, the set command must be used to send those packets to the null0 interface. This set command should be the final set command in the route map.

There are four possibilities for an incoming packet when route maps are in use. The following example illustrates all of them.

R2(config)#access-list 29 permit host 20.1.1.1

R2(config)#access-list 30 permit host 20.2.2.2

R2(config)#access-list 31 permit host 20.3.3.3

R2(config)#access-list 32 permit host 20.4.4.4

R2(config)#route-map EXAMPLE permit 10

R2(config-route-map)#match ip address 29

R2(config-route-map)#set ip next-hop 40.1.1.1

R2(config-route-map)#route-map EXAMPLE permit 20

R2(config-route-map)#match ip address 30

Assuming the route map has been applied to the router's ethernet0 interface, a packet sourced from 20.1.1.1 would meet the first line of the route map and have its next-hop IP address set to 40.1.1.1.

A packet sourced from 20.2.2.2 would match the next permit statement (sequence number 20). Since there is no action listed, this packet would return to the routing engine to undergo the normal routing procedure. All traffic that did not match these two addresses would also be routed normally - there would be no action taken by the route map.

Perhaps we want to specifically block traffic sourced from 20.3.3.3 or 20.4.4.4. We can use multiple match statements in one single route map, and have packets matching those two addresses sent to the bit bucket - the interface null0.

R2(config)#route-map EXAMPLE permit 30

R2(config-route-map)#match ip address 31

R2(config-route-map)#match ip address 32

R2(config-route-map)#set ?

as-path Prepend string for a BGP AS-path attribute

automatic-tag Automatically compute TAG value

comm-list set BGP community list (for deletion)

community BGP community attribute

dampening Set BGP route flap dampening parameters

default Set default information

extcommunity BGP extended community attribute

interface Output interface

ip IP specific information

level Where to import route

local-preference BGP local preference path attribute

metric Metric value for destination routing protocol

metric-type Type of metric for destination routing protocol

origin BGP origin code

tag Tag value for destination routing protocol

weight BGP weight for routing table

R2(config-route-map)#set interface null0

Any traffic matching ACLs 31 or 32 will be sent to null0, resulting in its being discarded by the router. Any traffic that didn't match any of the route map statements will be returned to the routing engine for normal processing.

Knowing policy routing and how to apply it are essential skills for passing the BSCI exam, earning your CCNP, and becoming more valuable in today's job market. Get some hands-on practice in a CCNA / CCNP home lab or rack rental to go along with learning the theory, and you'll be writing and applying policy routing in no time at all.
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com ), home of free CCNA and CCNP tutorials, and The Ultimate CCNA and CCNP Study Packages. For a copy of his FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies!

Cisco CCNP Certification/BCMSN Exam Tutorial: Uplinkfast

You remember from your CCNA studies that when a port goes through the transition from blocking to forwarding, you're looking at a 50-second delay before that port can actually begin forwarding frames. Configuring a port with PortFast is one way to get around that, but again, you can only use it when a single host device is found off the port. What if the device connected to a port is another switch?

A switch can be connected to two other switches, giving that local switch a redundant path to the root bridge, and that's great - we always want a backup plan! However, STP will only allow one path to be available, but if the available path to the root switch goes down, there will be a 50-second delay due to the STP timers MaxAge and ForwardDelay before the currently blocked path will be available.

The delay is there to prevent switching loops, and we can't use PortFast to shorten the delay since these are switches, not host devices. What we can use is Uplinkfast.

The ports that SW3 could potentially use to reach the root switch are collectively referred to as an uplink group. The uplink group includes the ports in forwarding and blocking mode. If the forwarding port in the uplink group sees that the link has gone down, another port in the uplink group will be transitioned from blocking to forwarding immediately. Uplinkfast is pretty much PortFast for wiring closets. (Cisco recommends that Uplinkfast not be used on switches in the distribution and core layers.)

Some additional details regarding Uplinkfast:

The actual transition from blocking to forwarding mode takes about three seconds.

Uplinkfast cannot be configured on a root switch.

Uplinkfast is configured globally. You can't run Uplinkfast on some ports or on a per-VLAN basis - it's all or nothing.

The original root port will become the root port again when it detects that its link to the root switch has come back up. This does not take place immediately. The switch uses the following formula to determine how long to wait before transitioning back to the forwarding state:

( 2 x FwdDelay) + 5 seconds

Uplinkfast will take immediate action to ensure that the switch upon which it is configured cannot become the root switch. First, the switch priority will be set to 49,152, which means that if all other switches are still at their default priority, they'd all have to go down before this switch can possibly become the root switch. Additionally, the STP Port Cost will be increased by 3000, making it highly unlikely that this switch will be used to reach the root switch by any downstream switches.

And you just know there's got to be at least one option with this command, right? Let's run IOS Help and see.

SW2(config)#spanning-tree uplinkfast ?

max-update-rate Rate at which station address updates are sent

When there is a direct link failure, dummy multicast frames are sent to the MAC destination 0100.0ccd.cdcd. The max-update-rate value determines how many of these frames will be sent in a 100-millisecond time period.

Mastering the details of UplinkFast, BackboneFast, BPDU Guard, and Loop Guard are vital to your success on the CCNP exams, and one or more of these features are in use on almost every network in the world. Learn these features for success in both the exam room and the real world!
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com). For a copy of his FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies! Daily exam questions and tutorials now available through RSS feed!

Cisco CCNP / BSCI Exam Tutorial: ISIS Router Types

To pass the BSCI exam and earn your CCNP, you've got to know ISIS inside and out. There are many similarities between ISIS and OSPF, but one major difference is that ISIS has three different types of routers - Level 1 (L1), Level 2 (L2), and L1/L2.

L1 routers are contained in a single area, and are connected to other areas by an L1/L2 router. The L1 uses the L1/L2 router as a default gateway to reach destinations contained in other areas, much like an OSPF stub router uses the ABR as a default gateway.

L1 routers have no specific routing table entries regarding any destination outside their own area; they will use an L1/L2 router as a default gateway to reach any external networks. ISIS L1 routers in the same area must synchronize their databases with each other.

Just as we have L1 routers, we also have L2 routers. Anytime we're routing between areas (inter-area routing), an L2 or L1/L2 router must be involved. All L2 routers will have synchronized databases as well.

Both L1 and L2 routers send out their own hellos. As with OSPF, hello packets allow ISIS routers to form adjacencies. The key difference here is that L1 routers send out L1 hellos, and L2 routers send out L2 hellos. If you have an L1 router and an L2 router on the same link, they will not form an adjacency.

An ISIS router can act as an L1 and an L2 router at the same time; these routers are L1/L2 routers. An L1/L2 router can have neighbors in separate ISIS areas. The L1/L2 router will have two separate databases, though - one for L1 routes and another for L2 routes. L1/L2 is the default setting for Cisco routers running ISIS. The L1/L2 router is the router that makes it possible for an L1 router to send data to another area.

In the next part of my ISIS tutorial, we'll take a more detailed look at those ISIS hellos!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNA and CCNP tutorials! For my FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies. Get your CCNA study guide from The Bryant Advantage!

Cisco CCNP / BCMSN Exam Tutorial: The Four (Or Five) STP Port States

As a CCNP candidate and a CCNA, you may be tempted to skip or just browse the many details of Spanning Tree Protocol. After all, you learned all of that in your CCNA studies, right? That's right, but it never hurts to review STP for a switching exam! Besides, many of us think of the four STP port states - but officially, there's a fifth one!

Disabled isn't generally thought of as an STP port state, but Cisco does officially consider this to be an STP state. A disabled port is one that is administratively shut down.

Once the port is opened, the port will go into blocking state. As the name implies, the port can't do much in this state - no frame forwarding, no frame receiving, and therefore no learning of MAC addresses. About the only thing this port can do is accept BPDUs from neighboring switches.

A port will then go from blocking mode into listening mode. The obvious question is "listening for what?" Listening for BPDUs - and this port can now send BPDUs as well. The port still can't forward or receive data frames.

When the port goes from listening mode to learning mode, it's getting ready to send and receive frames. In learning mode, the port begins to learn MAC addresses in preparation for adding them to its MAC address table.

Finally, a port can go into forwarding mode. This allows a port to forward and receive data frames, send and receive BPDUs, and place MAC addresses in its MAC table.

To see the STP mode of a given interface, use the show spanning-tree interface command.

SW1#show spanning-tree interface fast 0/11

Vlan Role Sts Cost Prio.Nbr Type

VLAN0001 Desg FWD 19 128.11 P2p

To see these states in action, shut a port down in your CCNA / CCNP home lab and continually run the show spanning interface command. Once you see this in action on real Cisco equipment, you'll have no problem with BCMSN exam questions. Just don't practice this or any other Cisco command on a production network!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNP and CCNA tutorials! For my FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies. Pass your CCNP exam with The Bryant Advantage!

Cisco CCNA / CCNP Home Lab Tutorial: Configuring An Access Server

As your CCNA / CCNP home lab expands, an access server such as the Cisco 2509 or 2511 is one of the best investments you can make. In this article, we'll look at the basic configuration for an access server and discuss how to connect to the other routers and switches in your pod through the AS.

Here's part of a configuration from one of my access servers:

ip host FRS 2006 100.1.1.1

ip host SW2 2005 100.1.1.1

ip host SW1 2004 100.1.1.1

ip host R2 2002 100.1.1.1

ip host R1 2001 100.1.1.1

ip host R3 2003 100.1.1.1

interface Loopback0

ip address 100.1.1.1 255.255.255.255

no ip directed-broadcast

This is an IP Host table, and this is what makes the entire AS setup work. Your PC will connect to the access server, and the access server is in turn physically connected to your other routers and switches via an octal cable. One end of the octal cable splices off into eight separate cables, each terminated with an Rj-45 connector. That connector will be placed into the console port of one of your home lab devices. In this configuration, I have connector 1 connected to the console port of R1, connector 2 to R2, connector 3 to R3, connector 4 to Sw1, and so forth. (The connectors are physically numbered as well.)

The IP Host table entries here are linked to the loopback address shown. The loopback can be any address, but it must match the address in the IP Host table. This allows you to create reverse telnet sessions to the routers and switches.

To open the reverse telnet sessions upon opening a connection to the AS, type the entire name of the device and press the enter key twice. A connection to that device will now be visible, as shown here:

Access_Server#r1

Trying R1 (100.1.1.1, 2001)... Open

R1#

To get back to the access server, use the key combination followed by pressing the "x" key. Keep doing this until you've opened a connection to every router and switch in your pod.

Once you've opened the lines, you will not use the full device name to connect to the home lab devices. You should press only the number corresponding to the reverse telnet session you opened. For instance, in this configuration I opened telnet session 1 to R1, session 2 to R2, and session 3 to R3. Once I opened those sessions, I just use those numbers to reconnect to the devices, as shown here:

Access_server#1

[Resuming connection 1 to r1 ... ]

R1#

Access_server#2

[Resuming connection 2 to r2 ... ]

R2#

Access_server#3

[Resuming connection 3 to r3 ... ]

R3#

If you type the full hostname again after initially opening the connection, you will see this message:

Access_server#r1

Trying R1 (100.1.1.1, 2001)...

% Connection refused by remote host

The connection is refused because you already have an open connection to that router.

There's one more important part of an access server config your CCNA / CCNP home lab will need:

line 1 8

no exec

transport input all

The line numbers may differ according to your access server, but "no exec" is very important here. This will stop rogue EXEC sessions from refusing connections that it shouldn't be refusing. Without this command, you'll commonly see "connection refused by remote host" when you shouldn't be. That message is the most common error you'll see on an access server, and it's there because you already have an open connection or you left "no exec" out of your configuration. "No exec" isn't mandatory, but it will help you keep your sanity!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNA and CCNP tutorials! For my FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies. Pass your CCNA exam with The Bryant Advantage!

Cisco / MCSE Exam Study: Creating A Road Map To Success

Planning for success on the CCNA, CCNP, and other Cisco exams is much like taking a trip in your car. You've got to plan ahead, accept the occasional detour, and just keep on going until you get there. But what do you do before you get started?

Create a road map - for success.

If you were driving from one side of the country to another, you certainly wouldn't just get in your car and start driving, would you? No. You would plan the trip out ahead of time. What would happen if you just got in the car and started driving in the hope that you would someday arrive at your final destination? You would never get there, and you'd spend a lot of time wandering aimlessly.

Don't spend your study time and slow your progress by studying for a Cisco exam without planning the trip. Schedule your study time as you would an appointment with a client, and keep that appointment. Make sure that your study time is quality study - turn your TV, iPod, and cell off. If you hit a bump in the road and don't get your certification the first time you take the exam, regroup and create another plan. Study until you get to the point that on exam day, you know that you are already a CCNA or CCNP and you're just there at the testing center to make it official.

The journey to success is not a straight line. When you look at a chart that shows a company's financial progress, the line never goes straight up. there are some ups and downs, but the overall result is success. The path to your eventual career and certification exam success may not be a direct one, but the important part is to get started - and to get any journey started, you've got to create a road map for a successful arrival at your destination.

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNP and CCNA tutorials! For my FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies. Pass your CCNP exam with The Bryant Advantage!

Cisco CCNA Certification and Career Path

Following your computer training toward your career path, you can go for the CCNA certification (Cisco Certified Network Associate), which indicates a foundation in the apprentice knowledge of networking. CCNA training allows you the ability for installations and operation of LAN, WAN, and dialup access services for small networks with 100 nodes or less.

The CCNA course includes, but not limited to use the different networking protocols such as Ethernet, Access Lists, Serial, IP, IGRP, Frame Relay, IP RIP, and VLANs. Cisco's CCNA Prep Center Pilot offers simulations and sample questions, besides the e-learning modules and laboratories.

Computer training includes also valuable tips from CCNA professionals, in addition to expert advice, and encouragement through CCNA certification success stories. CCNA training does not require any prerequisite and makes available many other resources to help students with the preparation of their CCNA certification exams.

CCNA course, exams and recommended training include the Introduction to Cisco Networking Technologies (INTRO), the Interconnecting Cisco Networking Devices (ICND) or both. CCNA training and additional training, probably cover most of your career path expectations.

However, Cisco's CCNA certifications are valid for 3 years, so it is necessary for additional computer training to re-certify. This is achieved by either passing the current CCNA exam at the moment of the original certification's expiration, passing the ICND exam, passing the 642 professional levels.

After CCNA training your can also re-certify by passing the Cisco Qualified Specialist exam, excluding the Sales Specialist exams, or passing a CCIE written exam, which is a re-certify form valid for individual who had a CCNA certification starting from October 1, 2004.

Cisco CCNA online training certification program, offers the same value, knowledge and skill earned on a traditional CCNA course, and it is a nationally recognized certification. With computer training online, you will gain knowledge of switched LAN Emulation networks, which are made up of Cisco original equipment.

CCNA training online focuses the coverage of Cisco router configuration procedures, mapped to exam objectives in order to prepare you for Cisco Exam 640-80, in partnership with major universities and colleges offering as well CCNA certification.

The Computer training program online consists of 2 sections; "Introduction to Network Engineering", allowing the student to understand the world of network engineering, learning fundamental facts of data network theory and current technologies making the Internet tick.

The second section of the online CCNA course, "Practical Network Engineering", is an approach to some of the most powerful networking technologies, involving extensive work on switches, Cisco routers, and firewalls in a simulated network environment, preparing students to earn the CCNA certification.

Natalie Aranda writes about business, training and certifications.

Cisco CCNA Certification Exam Tutorial: OSPF Hub-And-Spoke

 CCNA certification demands that you master the basics of OSPF, and for many studying for the CCNA exam, their first exposure to OSPF is a hub-and-spoke configuration. That's a tough way to get started, because a hub-and-spoke configuration built over an NBMA technology such as Frame Relay requires quite a bit of attention to detail. Let's take a quick look at several common OSPF configuration errors and how to avoid them on your CCNA test.

Make sure the hub is the designated router and that there are no backup designated routers. This is done by setting the OSPF interface priority to zero on the spoke routers. This not only ensures that the hub wins the DR election with its default OSPF interface priority of 1, but it prevents the spokes from ever having a chance to become the DR or BDR.

Configure neighbor statements on the hub. Since we're dealing with an NBMA network, the hub cannot dynamically discover its neighbors. Neighbor statements are not needed on the spokes. (They don't hurt anything, but they don't do anything, either.)

Finally, if your OSPF adjacencies do not form as expected, make sure to use your OSI model knowledge to approach the problem. The issue may actually be at Layer Two, with your Frame Relay configuration. If you don't use the "broadcast" option on your frame relay statements, OSPF hellos will not be transmitted successfully between potential neighbors. OSPF hellos are multicast, but the "broadcast" option for Frame Relay includes multicasts.

By paying special attention to these details, you're that much close to CCNA exam day success and earning your certification. I recommend that you get some experience with configuring OSPF hub-and-spoke before taking the CCNA exam, because it?s by actually performing tasks such as this that makes you supremely confident on CCNA test day.

Chris Bryant, CCIE  12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.

For a FREE copy of his latest e-books, ?How To Pass The CCNA? and ?How To Pass The CCNP?, visit the website and download your free copies. You can now get a FREE CCNA and CCNP exam question sent to your email inbox every day! Get your CCNA certification with The Bryant Advantage! chris@thebryantadvantage.com

 

Web Design Tools - San Jose, San Francisco, Oakland, Japan

"Web Design Tools - San Jose, San Francisco, Oakland, Japan Web designing entails use of a whole gamut of tools - for text, graphics, menus, animation, navigation design, color selection, font selection, authoring, programming and ecommerce development. The use of technologically advanced and effective tools ensure that the website attracts target audience and lists high in the search engines and directories.

Different tools are used in different aspects of web designing. Text links use HTML meta tags, graphic links use graphics along with navigation buttons, drop down menus use JavaScript and CGI among others, and special effects need tools such as Macromedia Flash and Adobe Photoshop. By far, Macromedia and Adobe Photoshop are the most commonly used tools in web design. Certain graphic designers also use Macromedia DreamWeaver. Flash helps in animation that if used well, can be an attractive feature in a website. Visual Basic is the most common language for scripting and SQL with other database engines are used for database management on the website. Templates are also used for the layout of a web page.

Apart from tools that make the site presentable and easily navigable, there are also content creation tools that help in creating Search Engine Optimized content. A word or a phrase, based on the worldwide searches is rated on tools such as Overture. Once the most popularly searched words in your industry are identified and short-listed, the content creators write content using these search words. This ensures that your website lists high in the search engines and directories. A combination of the right HTML text, background images, and graphic images with the right and most legible typefaces and fonts are required if the website has to be popular among your target audience.

Web promotion and ecommerce tools help in marketing your website. Pay-Per-Click Search Engine Promotion, Loyalty Programs, Email Campaigns and Online Games are some tools used for website promotion. Tools such as site statistics software and reporting from site searches let you know what exactly your visitors are looking for. The content and marketing strategies are then adjusted accordingly.

Apart from the tools, designing a good website also requires the skills and expertise of a range of professionals. A web site must essentially be written, programmed, and designed for the end users. A site that is written, coded and designed for user friendliness and search engine visibility gets the most traffic and results in boosting sales. Again, understanding the products, services or information that your target audience is looking for is important in the design, maintenance and re-design of your website.

"

I write articles for www.web-design.nr10.com, a San Francisco Web Development and Web Design Services, #10 is a Marketing and Technology Agency focused on delivering design, web technology development and e-business strategy solutions.

Cisco CCNP/BSCI Certification: BGP Route Reflector Tutorial

When you're studying for your BSCI exam and CCNP certification, you quickly realize that BGP is a whole new world from anything you've previously studies. One topic that sometimes confuses CCNP candidates is when a BGP route reflector needs to be configured. Route reflectors are an excellent workaround for a basic rule of BGP route advertisement that we?ll review in just a moment.

In the following example, the routers R1, R2, and R3 are all in BGP AS 100. This is not a full mesh, however. There are peer relationships between R1-R2 and R1-R3, but not between R2 and R3. R3 is advertising network 3.3.3.0/24 via BGP, and the route is seen on R1. R1's iBGP neighbor, R2 does not see the route, nor would any other iBGP neighbors of R1. Why?

A basic rule of BGP is that a BGP speaker cannot advertise a route to an iBGP neighbor if that route was learned from another iBGP neighbor. Configuring R1 as a route reflector will allow us to circumvent this rule. The entire route reflector process is transparent to the clients, and no configuration is necessary on those clients. We'll configure R1 as a route reflector for both R2 and R3.

R1(config)#router bgp 100

R1(config-router)#neighbor 172.12.123.2 route-reflector-client

3d18h: %BGP-5-ADJCHANGE: neighbor 172.12.123.2 Down RR client config change

R1(config-router)#neighbor 172.12.123.3 route-reflector-client

3d18h: %BGP-5-ADJCHANGE: neighbor 172.12.123.3 Down RR client config change

The BGP adjacencies do come down when this configuration is added, so this isn't something you want to do during a peak traffic time.

Once the adjacencies come back up, R2 will have the route to 3.3.3.0/24.

There are other possible solutions to this iBGP limitation, such as configuring BGP confederations. Those solutions are generally used on larger BGP deployments and with other concerns in mind, though, and configuring route reflectors serves this purpose just as well.

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages. For a FREE copy of his latest e-books, ?How To Pass The CCNA? and ?How To Pass The CCNP?, visit the website and download your free copies. Get your CCNA certification with The Bryant Advantage!

Cisco CCNP/BSCI Certification: Introduction To ISIS Terminology

When you're studying to pass the BSCI exam and earn your CCNP certification, you're going to be introduced to ISIS. ISIS and OSPF are both link-state protocols, but ISIS works quite differently from OSPF. You must master these details in order to earn your CCNP.

One of the major differences between OSPF and ISIS will be evident to you when you first begin your BSCI exam studies, and that is the terminology. ISIS uses terms that no other protocol you've studied to date uses, and learning these new terms is the first step to BSCI and CCNP exam success.

First off, what does "IS" stand for in "ISIS"? It stands for "Intermediate System", which sounds like a group of routers. As opposed to Autonomous Systems, which are logical groups of routers, an Intermediate System is simply a single router. That's it.

You'll also become familiar with End Systems, referred to in ISIS as an "ES". The End System is simply an end host.

ISIS and OSPF both use the concept of areas, but ISIS takes a different approach to this concept. ISIS routers use three different types of routing levels, according to the area a router has been placed in. Level 2 routers are connected only to the backbone and serve as a transit device between non-backbone areas. Level 1 routers are totally internal to a non-backbone area.

ISIS uses both Level-1 and Level-2 Hellos, meaning that the two types of routers just mentioned cannot form an adjacency. Luckily for us, there is a middle ground, and that is the Level 1-2 router. These routers connect non-backbone areas to backbone areas. L1-L2 routers keep two separate routing tables, one for L1 routing and another for L2 routing. This is the default setting for a Cisco router, and L1-L2 routers can form adjacencies with both L1 and L2 routers.

Part of the challenge of learning ISIS is getting used to the differences between ISIS and OSPF. Keep studying the terminology, master one concept at a time, and soon you'll be a master of ISIS and a CCNP to boot!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNP and CCNA tutorials! For my FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies. Earn your CCNP certification with The Bryant Advantage!

Cisco CCNA Certification: Cisco Switching Modes Tutorial

To pass the CCNA exam and earn that coveted certification, you've got to know Cisco switches inside and out. Among the many important details you've got to know are the three methods that Cisco switches use to forward frames, and the differences between the three.

The first switching method is Store-and-Forward. The name is the recipe, because that's just what the switch does - it stores the entire frame before beginning to forward it. This method allows for the greatest amount of error checking, since the Frame Check Sequence (FCS) can be run before the frame is forwarded. As always, there is a tradeoff, since this error checking process makes this the slowest of the three frame forwarding methods.

The quickest method is Cut-Through, where only the destination MAC address of the frame is examined before the forwarding process begins. This means that the part of the frame is actually being forwarded as it is still being received! The tradeoff here is that the FCS does not run, so there is absolutely no error checking with Cut-Through switching.

The middle ground between these two extremes is Fragment-Free, so named since fragmented frames will not be forwarded. The switch examines only the first 64 bytes of the frame for errors, since that is the part of the frame that will be damaged in case of a collision. There is error checking, but it is not as thorough as Store-and-Forward.

Keeping these three switching schemes straight is vital to your CCNA exam efforts, and it will help you in working with Cisco switches in the real world as well. Keep studying!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage , home of free CCNA and CCNP tutorials! Pass the CCNA exam with Chris Bryant!

Cisco CCNA Certification: Error Detection vs. Error Recovery

Passing the CCNA, Intro, and ICND exam is all about knowing and noticing the details. (Which makes perfect sense, since becoming a master networking administrator or engineer is also about noticing the details!) One such detail knows the difference between error detection and error recovery. While the terms are sometimes used interchangeably, they are not the same thing.

Error detection is just that - error detection only. Two common error detection methods are found at the Data Link layer of the OSI model, the FCS (Frame Check Sequence) and CRC (Cyclical Redundancy Check). A mathematical equation is run against the data in the frame, and the result is sent along with the data. The receiver runs the equation again, but this time. If the result is the same, the frame is considered valid; if the result is different, the frame is considered corrupt and is discarded.

Note that the FCS and CRC do nothing in regards to retransmission. They are strictly error detection schemes.

For an example of error recovery, we look to the Transport layer, where TCP runs. TCP performs reliable delivery, and the reason we call it "reliable" is that TCP uses sequence numbers to detect missing segments. If the sender determines from the sequence numbers that the remote host did not receive transmitted segments, the sender will retransmit the missing segments.

The key to keeping the terms straight in your head is to remember that while both error detection and error recovery both detect problems, only error recovery does anything about it. It's also worth reading an exam question twice when you see either term!

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (http://www.thebryantadvantage.com), home of free CCNA and CCNP tutorials! For my FREE "How To Pass The CCNA" or "CCNP" ebook, visit the website and download your copies. Earn your CCNA certification with The Bryant Advantage!